Good Afternoon, I have CR310, Am16/32 and 11 analog instruments, of which 4 are transducers and 7 are clinometers, the clinometers are biaxial and it have thermistor. Current I have a programming but includes only the part analog, my question is: How can I add the thermistor to the programming and connection of the am16/32?
Add programming:
'AM16/32B Program Example B-1
'Single-ended voltage measurements using MuxSelect()
'CR300-series data loggers
'Multiplexer (mux) in 4X16 Mode
'Wiring:
'Data logger to AM16/32B
'Signal Ground (CR300) to COM ODD H (AM16/32B)
'1H (CR300) to COM ODD L (AM16/32B)
'1L (CR300) to COM EVEN H (AM16/32B)
'2H (CR300) to COM EVEN L (AM16/32B)
'Ground (CR300) to COM ground (AM16/32B)
'SW12V (CR300) to 12V (AM16/32B)
'G (CR300) to G (AM16/32B)
'C1 (CR300) to CLK (AM16/32B)
'C2 (CR300) to RES (AM16/32B)
'AM16/32B to Sensors
'1H terminal (AM16/32B) to Sensor 1, 2, and 3 grounds
'1L terminal (Am16/32B) to Sensor 1 signal
'2H terminal (AM16/32B) to Sensor 2 signal
'2L terminal (AM16/32B) to Sensor 3 signal
'Ground (AM16/32B) to Sensor 1, 2, and 3 shields
'Repeat wiring pattern (H/L/H/L/Ground) in the next blue SET
'for each additional trio of sensors.
'Declare variables
Public SEVolt(9)
Units SEVolt=mV
'Define Data Tables
DataTable (Hourly,True,-1)
DataInterval(0,60,Min,10)
Sample(9,SEVolt(),FP2)
EndTable
DataTable(Daily,True,-1)
DataInterval(0,1440,Min,10)
Average (9,SEVolt(),FP2,False)
EndTable
'Main Program'
BeginProg
SW12 (1 ) 'provide power to AM16/32B
'Main Scan
Scan(30,Sec,1,0)
'>>>>>> SET 1
'Turn AM16/32B Multiplexer On, start measurements on multiplexer channel 1
MuxSelect (C1,C2 ,20,1,1)
'3 repetitions, writing to SEVolt(1), SEVolt(2) and SEVolt(3)
'3 repetitions, measuring 1L, 2H, 2L on multiplexer
VoltSe(SEVolt(1),3,mv2500,1,True,0,60,1,0)
'>>>>>> SET 2
PulsePort (C1 ,10000) 'to move to SET 2
'3 repetitions, writing to SEVolt(4), SEVolt(5) and SEVolt(6)
'3 repetitions, measuring 3L, 4H, 4L on multiplexer
VoltSe(SEVolt(4),3,mv2500,1,True,0,60,1,0)
'>>>>>> SET 3
PulsePort (C1 ,10000) 'to move to SET 3
'3 repetitions, writing to SEVolt(7), SEVolt(8) and SEVolt(9)
'3 repetitions, measuring 5L, 6H, 6L on multiplexer
VoltSe(SEVolt(7),3,mv2500,1,True,0,60,1,0)
'Turn AM16/32B Multiplexer Off
PortSet(C2,0)
'Call Data Tables and Store Data
CallTable Hourly
CallTable Daily
NextScan
EndProg
This post is under review.
Buen dia, podrian atender mi duda, se lo agradeceria bastante